Manganese carbonide is a stable, manganese-carbonoid compound. Mn3C has the chemical formula and is about 1.520degC at melting point. Its density is 6.89g/cm3.
Particle Size: 325mesh
Purity: 99%
About Manganese Carbide Mn3C Powder:
Manganese carbide
It is made from carbon and manganese.
Manganese carbide
Formula
What is Mn3C?
Manganese carbide
melting point
It is approximately 1520°C
Manganese carbide
The density
6.89g/cm3. Manganese carbide burns quickly in oxygen, and is decomposed in water to make manganese hydrogenxide and methane. It can be easily reduced to acid, decomposed by chlorine or fluorine, and can also react well with fluorine and chlorine.
The heat of the formation of manganese carbide is ^fHm (298K)=-(15.06+-12.55)kJ/mol. The result of smelting manganese-silicon or high-carbon ferromangannese in an electric furnace or blast furnace is manganese carbide. This means that the heat absorption by the reaction will be less than for reduction to metallic manganese, or manganese silicide. It starts
With
It is cold. The high-carbon ferromanganese is therefore more carbon.
To receive the most current information, send us an inquiry
Manganese carbide
Prices
Please fill out the form below if you wish to
buy Manganese Carbide Powder
In bulk.
Manganese Carbide Mn3C powder performance:
Mn3C has the following physical characteristics: Mn3C is a hard crystalline solid, or bright needle crystal. Its relative density is 6.89. Concentrated sulfuric acid or nitric Acid will insoluble it, however, water or dilute acids can decompose it to create manganese hydroxide and other hydrocarbons. It is easily reacted with fluorine or chlorine, and it burns fast in oxygen.
Technical Parameters of Manganese Carbide, Mn3C Powder
|
Certificate for Mn3C powder
|
|
Purity
|
C
|
P
|
S
|
O
|
Get carbon free
|
Size for Particel
|
|
>99%
|
5.91
|
0.03
|
0.03
|
0.3
|
0.2
|
D50=11mm, -325mesh
|
The gas-based reduction manganese oxide is a method of making manganese carbide. Once you have mixed manganese dioxide, water, binder, and dried, the dry block can be placed in an atmosphere with H2, CH4, CO, N2, and N2. Then, it is calcined at 1100 1300, which is manganese carbide. Here are the specific steps. The mass percent of -325 mesh size refers to 90% of analytically purified manganese dioxide. It is also mixed with trimanganese trioxidide and 0.5% CMC. Finally, it is pelletized and dried. After drying, the sample is placed in an atmosphere of 10% CMC, 30% H2, 10% CO and 50% N2. The calcination temperature was 1150degC with a time of 120min. After cooling down to room temperature the obtained manganese carbide product can be converted into manganese dioxide at 95%.
Applicaciones
Manganese Carbide Mn3C Powder:
Manganese carbonide Mn3C powder can be used to make hard coatings, target, weld materials, and spray tools. It is also used in the steelmaking industry, aerospace, and many other areas.
The grain refiner of Cermet and Wolfen carbide, manganese carbonide has the ability to significantly enhance the alloy's characteristics.
Manganese troxide is an important raw material in the manufacture of soft magnetic materials of manganese, zinc ferrite and other electronic materials. This is why it is so widely used.
To prepare transformer oils, you can use manganese carbonide. The process is straightforward and can be scaled up for production on a large scale. This will allow you to prolong the lifespan of your transformer oil, as well as reduce safety hazards.
Manganese Carbide, Mn3C powder storage conditions:
Manganese Carbide, Mn3C Powder, should be maintained in a dry, cool, and sealed environment.
Shipping Manganese Carbide Mn3C powder:
You can pack it in two plastic bags with the inside.
Manganese Carbide Mn3C Powder packing: vacuum packing, 100g, 500g or 1kg/bag, 25kg/barrel, or as your request.
Manganese Carbide Mn3C Powder shipping:
Could be sent by sea, air, or express, as soon after receipt of payment.
Jatujakguide advanced materials Nano Technology Co. Ltd., (Jatujakguide), is a reliable global supplier and manufacturer. They have over 12 years of experience in manufacturing super high-quality chemicals, Nanomaterials and boride powders.
Send us an enquiry if you're looking for Manganese Carbide Powder of high-quality. (
brad@ihpa.net
)